• Font Size:
  • A
  • A
  • A

Ask the Experts

Ask the Experts

Ask a Question


Find the Answers You Need. Ask Questions that Matter to You.

Ask one of our experts a question or search below to see Q & A threads in your area of interest.

Category: Frame Grabbers & Other Imaging Boards

I am running SaperaLT 7.10.00.1022 and WiT 8.3 when I start my WiT program I get an CORAPI.dll is missing messaage. But it isn't actually missing. And when I ok that message I get wsapera.dll failed to load message. Do you know what I have to do to fix this?

1 Reply » Click Here

Hi, I have been using a PCI framgrabber card for video acquisition and used to process the video for real-time object recognition. Now we are planning to shift to external framegrabber by Pleora iport framegrabber. This captures video from analog video source and converts to GigE, which in turn is connected to the PC via network switch, and run object recognition algorithms on the video. Is this a good option for real-time video acquisition and processing for pattern recognition tasks? Are there any frame drops in this setup? Does GigE Vision software handle this kind of data and provide processing libraries for object recognition tasks? Please advise. Thanks and regards.

2 Replies » Click Here

We are using several cameras using camera link Is it a generic SDK which make us able to write an interface usable on any camera? Is it in Camera Link specifications a definition of time stamp and image counter?

2 Replies » Click Here

Do you know of a product or solution to converter 1080P camera link to DVI ?

1 Reply » Click Here

I am using Halcon 11 to grab images form a Teledyne DALSA Xcellera frame grabber board. I am using Sapera Lt version 7.3. I have used your program to print out all of the parameters that can be read from the board. The program I am using is 'Saperalt_parameters.hdev' and with the correct camera file I can print out all of the parameters. The Xcellera frame grabber board supports 4 digital output lines and 4 digital input lines and information about these lines are not printed out. The Saperalt has a special program called GeneralIO which controlls and reads these ports. Do you have a driver that supports these ports and if not, could you support these ports in Halcon ll?

1 Reply » Click Here

Hello, I have an imager which outputs digital data with 25 MHz, 8 Bit parallel data, Clock, HSYNC and VSYNC. I want to grab this frames over Ethernet. Is there a device which can handle this? I found only some devices with other interfaces. Best regards, Stefan

1 Reply » Click Here

I used to communicate CAMLINK to PCI board. (Mode full configuration) I want to "4Tap 14bit". Your set-up file is 8Tap 8bit.

3 Replies » Click Here

I'm developing an application for the acquisition by linescan with Xilinx ML605. I developed an IP that manages the LVD signal correctly. I can read the clock output from linescan and I can deserialize the data acquisition using a PLL. But, I have a problem with the correctly deserialization of data. I request the last update of Clink’s standard but I don’t find the position of data for deserialize. The problem consists in the identification of the bits of the pixels on the data lines. Thank you for your attention.

3 Replies » Click Here

I have an older vision system on a process that is working well. The concern is obsolescence. The system uses a Coreco PCVision PCI card in an NT based PC. I would like to set up a back up system, hopefully using newer OS such as XP. Would like to find contacts who had experience with these and could enlighten me during my upgrade backup journey. The vendor that supplied the system no longer supports it and no longer has the knowledge of these systems. Thank you in advance

3 Replies » Click Here

I wish to watch a surface move, and calculate its travel distance. In effect, I wish to copy the action of a non-contact mouse. Grab a frame - wait - Grab a frame - Determine pixels the image shifted. At 200 inches per second, in an embedded application - no PC, very hostel environment. Is this Possible - If so how?

1 Reply » Click Here

Hello: My Customer uses the Matrox Solios Series Image Card. In 32bit OS, if the System Memory is over 2GB, the Matrox Solios Series Image Card will use 512MB~1GB Memory of the System. Please Help us to find the solution for my Customer. Thanks.

1 Reply » Click Here

We are microcontroller based Industrial Equipment Designers and manufacturers for various industries and are interested in manufacturing Color CCD camera based food grain sorters. Please assist us in selecting the right camera .

1 Reply » Click Here

I have analog cameras with 4 channel PC cards and corresponding software for digital video recorders, and desktop applications. How can I connect the acquired image to NI Vision, which only recognizes USB cameras on my computer?

1 Reply » Click Here

Search AIA:


Browse by Products:


Browse by Company Type: